switch holder.scad

[things.git] / diffuser-adjustable.scad

diff --git a/diffuser-adjustable.scad b/diffuser-adjustable.scad
index 8c47adfe62643c3afea88373249f7221657c463e..624c5d858649f30ba446ec07ab5c379548b4b03f 100644 (file)
--- a/diffuser-adjustable.scad
+++ b/diffuser-adjustable.scad
@@ -10,23 +10,25 @@
 // For any other flashlight, adjust the parameters below:
 
 // the true _diameter_ of the flashlight + some space around
-ring_d = 34.3 + 1.0;
+// ring_d = 34.3 + 1.0; // zsj-t29
+ring_d = 44 + 0.5; // lzz-186
 
 // the diaphragm thickness, set so that it is printed with two print layers
-diaphragm = 0.5;
+diaphragm = 0.4;
 
 // outer wall thickness - preferably the integer multiple
 // of the print trace width
-wall = 1.5;
+wall = 1.0;
 
 // height of the center of clip beams + some space below + diaphragm thickness
-clip_h = 7.3 + 0.5 + diaphragm;
+// clip_h = 7.3 + 0.5 + diaphragm; // zsj-t29
+clip_h = 16 + 0.5 + diaphragm; // zsj-t29
 
 // the clips protrude this much to the inner cylindrical hole
 // the bigger value means more stiff fit
 clip_w = 1.2;
 
-clip_angle = 120; // at least 90 degrees; bigger is easier to put on and off,
+clip_angle = 90; // at least 90 degrees; bigger is easier to put on and off,
        // smaller is more stiff, but harder to remove
 
 n_clips = 3; // number of clips; odd numbers prefered
@@ -35,20 +37,30 @@ n_clips = 3; // number of clips; odd numbers prefered
 // on top of the clip
 clip_top = clip_h + (clip_w+wall/2)*tan(clip_angle/2);
 
+// if the lens protrudes below the outer ring, it is better that
+// the diffuser sits on the outer ring. So we can add an additional
+// support ring
+support_h = 3;
+support_w = 3;
+
 // the overall height:
-// ring_h = clip_top; // cylindrical shape without the clips protruding on the top
-ring_h = clip_h + wall; // clips protruding on the top
+ring_h = clip_top; // cylindrical shape without the clips protruding on the top
+// ring_h = clip_h + wall; // clips protruding on the top
 
 infty = 100;
 eps = 0.01;
 
 module diffuser() {
        difference() {
+               $fn = 256;
                // outer cylinder
                cylinder(r = ring_d/2 + wall, h = ring_h);
-               // inner cylinder hole + diaphragm
+               // inner cylinder hole
+               translate([0, 0, diaphragm + support_h])
+                       cylinder(r = ring_d/2, h = ring_h - support_h);
+               // support ring
                translate([0, 0, diaphragm])
-                       cylinder(r = ring_d/2, h = ring_h);
+                       cylinder(r = ring_d/2 - support_w, h = support_h + eps);
                translate([0, 0, ring_h + eps - wall])
                        cylinder(r1 = ring_d/2, r2 = ring_d/2 + wall/2, h = wall);
        }
@@ -61,7 +73,7 @@ module diffuser() {
                                rotate([0, clip_angle/2, 0])
                                        cube(infty);
                        }
-               cylinder(r = ring_d/2 + wall, h = clip_top);
+               cylinder(r = ring_d/2 + wall, h = clip_top, $fn = 256);
        }
 }