From 114123230346ffb55488189a1a95182e8cece162 Mon Sep 17 00:00:00 2001
From: "Jan \"Yenya\" Kasprzak" <kas@fi.muni.cz>
Date: Fri, 17 Jan 2014 13:09:00 +0100
Subject: [PATCH] case.scad: different approach to rear mounting holes

---
 case.scad | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/case.scad b/case.scad
index b1e5a3f..cb028f6 100644
--- a/case.scad
+++ b/case.scad
@@ -1,4 +1,4 @@
-lowres = 0;
+lowres = 0; // fast rendering or fine printing with print-friendly orientation
 
 eps = 0.01;
 infty = 300;
@@ -40,6 +40,9 @@ pcb_xoff = 90 * 25.4/1000; // offset of the LED from the middle of the PCB
 prg_len = 10; // programming connector
 prg_width = 7;
 
+rear_clip_hole_dist = 10; // distance between the holes in the rear clip
+rear_clip_aspect = 0.35; // w/h aspect ratio of the ellipse of the rear clip
+
 module case_body() {
 	hull() {
 		translate([-batt_len/2-2*wall-cable_sep, -batt_diam/2-wall, 0])
@@ -57,6 +60,12 @@ module case_body() {
 			-batt_diam/2-2*pcb_comp_h-pcb_thick-wall])
 			cube([front_flat_len, pcb_width+wall, eps]);
 	};
+	for (x = [-1, 1]) scale([x, 1, 1]) hull() {
+		for (x0 = [0-wall, 10+wall])
+			translate([batt_len/2-wall-wire_thick-x0, batt_diam/2, 0])
+				rotate([-90, 0, 0]) scale([rear_clip_aspect, 1, 1])
+				cylinder(r=batt_diam/2 + 2*wall + wire_thick, h=wall);
+		};
 };
 
 module case() {
@@ -164,7 +173,7 @@ module case() {
 			vert_torus();
 			
 		for (x = [-1, 1]) scale([x, 1, 1]) for (x0 = [0, 10])
-			translate([batt_len/2-wall-wire_thick-x0, 0, batt_end_h-wire_thick/2])
+			translate([batt_len/2-wall-wire_thick-x0, 0, batt_diam/2+wire_thick/2+wall])
 			rotate([-90, 0, 0])
 			scale([2,1,1]) cylinder (r=wire_thick/2, h=infty, $fn=16);
 	};
@@ -213,6 +222,13 @@ module lid() {
 			translate([-batt_len/2-cable_sep-wall, batt_diam/2-pcb_width+0.5*wall+0.5*lid_sep, batt_diam/2 + pcb_comp_h+pcb_thick-wall-lid_sep])
 			cube([batt_len + 2*wall + 2* cable_sep, pcb_width-1.5*wall-1.5*lid_sep, eps]);
 		};
+		// holes for the mounting clips on the body
+		for (x = [-1, 1]) scale([x, 1, 1]) hull() {
+		for (x0 = [0-wall, 10+wall])
+			translate([batt_len/2-wall-wire_thick-x0, batt_diam/2-lid_sep+eps, 0])
+				rotate([-90, 0, 0]) scale([rear_clip_aspect, 1, 1])
+				cylinder(r=batt_diam/2 + 2*wall + wire_thick+lid_sep/rear_clip_aspect, h=wall+lid_sep+eps);
+		};
 	};
 };
 
-- 
2.39.3