X-Git-Url: https://www.fi.muni.cz/~kas/git//home/kas/public_html/git/?p=heater.git;a=blobdiff_plain;f=heater-base.scad;fp=heater-base.scad;h=0000000000000000000000000000000000000000;hp=a3a5706e70770ca1a9e69c1e2793c1d5fd5a6b8d;hb=8869cb3a648a8e9d90093cd7d936a54e87e0941c;hpb=62e66db3d05dc177bf08d8ce365f582fafbf63a4

diff --git a/heater-base.scad b/heater-base.scad
deleted file mode 100644
index a3a5706..0000000
--- a/heater-base.scad
+++ /dev/null
@@ -1,87 +0,0 @@
-// 18650 is ~18mm diameter, ~65mm length, 
-batt_diam = 18;
-batt_len = 65+1;
-batt_clip_h = 0.75 * batt_diam;
-wall = 2.2;
-
-eps = 0.01;
-infty = 300;
-
-pcb_len = 36;
-pcb_thick = 1.3;
-pcb_groove = 2;
-pcb_width = 11;
-pcb_clip_off = 5;
-pcb_clip_w = 8;
-
-wire_thick = 2;
-wire_sep = 3;
-
-translate([0, -batt_diam/2-wall-pcb_thick/2+eps, 0])
-difference() {
-	union() {
-		// lower part of the PCB holder
-		translate([0, 0, (pcb_groove + wall) / 2])
-			cube([pcb_len + 2*wall, pcb_thick + 2*wall, pcb_groove + wall], center=true);
-		// rear part of the PCB holder (behind S1)
-		translate([pcb_clip_off, 0, 0])
-			cube([pcb_clip_w, pcb_thick/2+wall/2, pcb_width + 2*wall]);
-		// side part of the PCB holder (near the battery wires)
-		translate([-pcb_len/2-wall, -pcb_thick/2-wall, 0])
-			cube([pcb_groove+wall, pcb_thick+1.5*wall, pcb_width + 2*wall]);
-	};
-	// the PCB itself
-	translate([0, 0, wall + pcb_width/2])
-		cube([pcb_len, pcb_thick, pcb_width+eps], center=true);
-};
-
-difference() {
-	union() {
-		// lower part of the battery holder
-		translate([0, 0, pcb_groove/2 + wall/2])
-			cube([batt_len + 2*wall, batt_diam + 2*wall, pcb_groove + wall],
-			center=true);
-		// rear part of the battery clip
-		translate([-(batt_len/2-pcb_len/2+pcb_groove+wall)/2-pcb_len/2+pcb_groove, 0, batt_clip_h/2+wall/2])
-			cube([batt_len/2-pcb_len/2+pcb_groove + wall, batt_diam + 2*wall, batt_clip_h + wall], center=true);
-		// front (+) part of the battery clip
-		translate([batt_len/2+wall/2, 0, batt_clip_h/2+wall/2])
-			hull() {
-				cube([wall, batt_diam + 2*wall, batt_clip_h + wall], center=true); 
-				translate([-10/2, 0, -batt_clip_h/2])
-				cube([10, batt_diam+2*wall, wall], center=true);
-			};
-		// middle clips
-		translate([pcb_clip_off+pcb_clip_w/2, 0, batt_clip_h/2+wall/2])
-			hull() {
-				cube([pcb_clip_w, batt_diam + 2*wall, batt_clip_h + wall], center=true);
-				translate([0, 0, -batt_clip_h/2])
-				cube([2*pcb_clip_w, batt_diam+2*wall, wall], center=true);
-			};
-	};
-	// battery
-	translate([-batt_len/2, 0, batt_diam/2+wall])
-		rotate([0, 90, 0])
-		cylinder(r=batt_diam/2, h = batt_len);
-	// top part rounded
-	difference() {
-		translate([0, 0, infty/4 + wall + batt_diam/2])
-			cube([infty/2, infty/2, infty/2], center=true);
-		translate([-infty/2, 0, batt_diam/2+wall])
-			rotate([0, 90, 0])
-			cylinder(r=batt_diam/2+wall, h = infty);
-	};
-	// wire holes
-	for (j=[-wire_sep/2, wire_sep/2]) 
-	for (i=[-wire_sep/2, wire_sep/2]) 
-	translate([-infty/2, i, batt_diam/2 + wall+j])
-		rotate([0, 90, 0])
-		rotate([0, 0, 90])
-		cylinder(r=wire_thick/2, h = infty, $fn=6);
-
-	translate([-infty/2, -batt_diam/2, wall + pcb_groove + wire_thick/2])
-		rotate([0, 90, 0])
-		rotate([0, 0, 90])
-		cylinder(r=wire_thick/2, h = infty, $fn=6);
-};
-