infty = 100;
debug = 0;
-heatsink_thickness = 2.5;
-heatsink_width = 18-3.4;
-heatsink_length = 58;
+wall_thickness = 1.5;
+fraen_diam = 30.90;
+fraen_h = 29.3;
+pin_diam = 4;
+pin_offset = 10.35*1.4142;
+pin_len = 9.2;
+front_add = 4;
+
+rear_pin_dist = 9.1;
+rear_pin_diam = 3.25;
+
+side_barrier_x_offset = 13;
+side_barrier_pin_z_offset = 4.2;
+side_barrier_thickness = 2;
+heatsink_thickness = 2;
+
+clip_h1 = 27; // front height (on the heatsink side)
+clip_h2 = 20; // rear height (on the lens side)
+clip_l = 28;
+clip_wall = wall_thickness;
+clip_space = 3.5;
+clip_bolt1_z = 6;
+clip_bolt1_x = 19.5;
+clip_bolt2_z = 22;
+clip_bolt2_x = 21;
+clip_angle = 18;
+clip_top_xoff = clip_l*tan(clip_angle);
+
+clip_y_off = 34;
+clip_x_off = 2;
+clip_x_rot = -3;
+
+// z-axis is up
module bolt_mount(d, h, w1, w2, fn) {
difference() {
translate([0, 0, -epsilon])
};
};
-clip_h1 = 25; // inner height
-clip_h2 = 18; // inner height
-clip_l = 35;
-clip_wall = 2;
-clip_space = 4;
-clip_bolt1_x = 10;
-clip_bolt2_x = 25;
-
-module clip_top_circle() {
- rotate([-90, 0, 0])
- difference() {
- translate([-clip_space/2, 0, 0])
- cylinder(r=clip_wall, h = epsilon, $fn=32);
- translate([-infty/2, clip_wall/2-epsilon, -epsilon])
- cube(infty);
- translate([clip_wall+epsilon, -infty/2, -epsilon])
- cube(infty);
- };
-};
-
module seat_clip() {
difference() {
- polyhedron(points = [
- [-clip_wall-clip_space/2, 0, clip_h1/2+clip_wall],
- [-clip_wall-clip_space/2, clip_l, clip_h2/2+clip_wall],
- [-clip_wall-clip_space/2, clip_l, -clip_h2/2],
- [-clip_wall-clip_space/2, 0, -clip_h1/2],
- [ clip_wall+clip_space/2, 0, clip_h1/2+clip_wall],
- [ clip_wall+clip_space/2, clip_l, clip_h2/2+clip_wall],
- [ clip_wall+clip_space/2, clip_l, -clip_h2/2],
- [ clip_wall+clip_space/2, 0, -clip_h1/2],
- ], triangles = [
- [0, 2, 1], [3, 2, 0], [4, 5, 6], [6, 7, 4],
- [0, 1, 5], [5, 4, 0], [2, 3, 7], [7, 6, 2],
- [1, 2, 6], [6, 5, 1], [0, 7, 3], [7, 0, 4],
- ]);
- polyhedron(points = [
- [-clip_space/2, -epsilon, clip_h1/2],
- [-clip_space/2, clip_l+epsilon, clip_h2/2],
- [-clip_space/2, clip_l+epsilon, -clip_h2/2-epsilon],
- [-clip_space/2, -epsilon, -clip_h1/2-epsilon],
- [ clip_space/2, -epsilon, clip_h1/2],
- [ clip_space/2, clip_l+epsilon, clip_h2/2],
- [ clip_space/2, clip_l+epsilon, -clip_h2/2-epsilon],
- [ clip_space/2, -epsilon, -clip_h1/2-epsilon],
- ], triangles = [
- [0, 2, 1], [3, 2, 0], [4, 5, 6], [6, 7, 4],
- [0, 1, 5], [5, 4, 0], [2, 3, 7], [7, 6, 2],
- [1, 2, 6], [6, 5, 1], [0, 7, 3], [7, 0, 4],
- ]);
- // bolt holes
- translate([0, clip_bolt1_x, 0])
- rotate([0, 90, 0])
- translate([0, 0, -clip_wall-clip_space/2-epsilon])
- cylinder(r=2, h=2*clip_wall+clip_space+2*epsilon,
- $fn = 6);
- translate([0, clip_bolt2_x, 0])
- rotate([0, 90, 0])
- translate([0, 0, -clip_wall-clip_space/2-epsilon])
- cylinder(r=2, h=2*clip_wall+clip_space+2*epsilon,
- $fn=6);
- };
-
- translate([-clip_space, clip_bolt1_x, 0])
- rotate([0, -90, 0])
- bolt_mount(6, 3, 7, 14, 6);
-
- translate([-clip_space, clip_bolt2_x, 0])
- rotate([0, -90, 0])
- bolt_mount(6, 3, 7, 14, 6);
+ union() {
+ // right part
+ hull() {
+ translate([0, clip_space/2, 0])
+ cube([clip_h1, clip_wall, epsilon]);
+ translate([clip_top_xoff, clip_space/2, clip_l])
+ cube([clip_h2, clip_wall, epsilon]);
+ };
- translate([clip_space, clip_bolt1_x, 0])
- rotate([0, 90, 0])
- bolt_mount(6, 3, 7, 14, 128);
+ // left part
+ hull() {
+ translate([0, -clip_space/2-clip_wall, 0])
+ cube([clip_h1, clip_wall, epsilon]);
+ translate([0+clip_top_xoff, -clip_space/2-clip_wall, clip_l])
+ cube([clip_h2, clip_wall, epsilon]);
+ };
- translate([clip_space, clip_bolt2_x, 0])
- rotate([0, 90, 0])
- bolt_mount(6, 3, 7, 14, 128);
-};
+ // top part
+ hull() {
+ translate([-2*clip_wall, -clip_space/2-clip_wall, 0])
+ cube([2*clip_wall+epsilon, 2*clip_wall+clip_space, epsilon]);
+ translate([-clip_wall+clip_top_xoff, -clip_space/2-clip_wall, clip_l])
+ cube([clip_wall+epsilon, 2*clip_wall+clip_space, epsilon]);
+ };
-/*
-seat_clip();
+ // bolt mounts
+ translate([clip_bolt1_x, clip_space/2 + clip_wall, clip_bolt1_z])
+ rotate([-90, 0, 0])
+ bolt_mount(6.5, 2, 7, 12, 6);
-difference() {
- union() {
- hull() {
- translate([40, epsilon, 2])
- clip_top();
- clip_top();
- };
+ translate([clip_bolt1_x, -clip_space/2 - clip_wall, clip_bolt1_z])
+ rotate([90, 0, 0])
+ bolt_mount(6.5, 2, 7, 12, 32);
- translate([40, 0, 25])
+ translate([clip_bolt2_x, clip_space/2 + clip_wall, clip_bolt2_z])
rotate([-90, 0, 0])
- cylinder(r=34/2, h=clip_l);
+ bolt_mount(6.5, 2, 7, 12, 6);
- hull() {
- translate([clip_space/2+epsilon, 0, 0])
- cube([clip_wall-epsilon, clip_wall, clip_h1/2+2*clip_wall-epsilon]);
- translate([40, 0, 14+epsilon])
- cube([clip_wall-epsilon, clip_wall, 34/2]);
- };
- };
- translate([40, 6, 25])
- rotate([-90, 0, 0]) {
- cylinder(r=31/2, h=clip_l);
- fraen_lens();
- heatsink();
+ translate([clip_bolt2_x, -clip_space/2 - clip_wall, clip_bolt2_z])
+ rotate([90, 0, 0])
+ bolt_mount(6.5, 2, 7, 12, 32);
};
-};
-*/
-
-wall_thickness = 1.5;
-fraen_diam = 30.75;
-fraen_h = 29.8;
-pin_diam = 4;
-pin_offset = 10.35*1.4142;
-pin_len = 9.2;
-front_add = 4;
+ // bolt holes
+ translate([clip_bolt1_x, infty/2, clip_bolt1_z])
+ rotate([90, 0, 0])
+ cylinder(r=2, h=infty, $fn = 6);
+ translate([clip_bolt2_x, infty/2, clip_bolt2_z])
+ rotate([90, 0, 0])
+ cylinder(r=2, h=infty, $fn = 6);
+ }
-side_barrier_x_offset = 13;
-side_barrier_pin_z_offset = 4.2;
-side_barrier_thickness = 2;
+}
+// upper part of the lens holder
module round_part() {
difference() {
cylinder(r = fraen_diam/2 + pin_diam/2 + wall_thickness,
rotate([0, 0, angle+45])
translate([pin_offset, 0, -epsilon])
cylinder(r=pin_diam/2,
- h=epsilon, $fn=32);
+ h=epsilon);
};
}
translate([0, 0, pin_len + 0.5*wall_thickness - epsilon])
cylinder(r1 = fraen_diam/2,
r2 = (fraen_diam+pin_diam + wall_thickness)/2,
- h = front_add + 2*epsilon);
+ h = front_add - 0.5*wall_thickness+ 2*epsilon);
// pin holes
for (angle = [0, 90, 180, 270]) {
rotate([0, 0, angle+45])
translate([pin_offset, 0, epsilon])
cylinder(r=pin_diam/2,
- h=pin_len+epsilon, $fn=32);
+ h=pin_len+epsilon);
};
};
intersection() {
cylinder(r=fraen_diam/2+epsilon, h=infty);
translate([-infty/2, side_barrier_x_offset,
- wall_thickness + pin_len - side_barrier_pin_z_offset - side_barrier_thickness ])
+ pin_len - side_barrier_pin_z_offset - side_barrier_thickness ])
cube([infty, infty, side_barrier_thickness]);
};
};
h = epsilon);
for (angle = [0, 90, 180, 270])
rotate([0, 0, angle])
- translate([9.1, 9.1, 0])
+ translate([rear_pin_dist, rear_pin_dist, 0])
cylinder(r=wall_thickness+3.75/2, h = epsilon);
}
hull() {
h = epsilon);
for (angle = [0, 90, 180, 270]) {
rotate([0, 0, angle])
- translate([9.1, 9.1, -epsilon])
+ translate([rear_pin_dist, rear_pin_dist, -epsilon])
cylinder(r=3.75/2, h = epsilon);
rotate([0, 0, angle+45])
translate([pin_offset, 0, fraen_h - pin_len + epsilon])
cylinder(r=pin_diam/2,
- h=epsilon, $fn=32);
+ h=epsilon);
}
}
}
}
-rear_spring_w = 4;
+rear_spring_w = 2*rear_pin_dist-rear_pin_diam-2;
+rear_spring_h = 1.5;
+rear_spring_center_w = 4;
+led_zoff = 6;
module rear_spring() {
translate([0, 0, wall_thickness/2])
- cube([18+2*wall_thickness+3.5, rear_spring_w, wall_thickness], center=true);
- difference() {
- rotate([90, 0, 0])
- translate([0, 0, -rear_spring_w/2])
- cylinder(r=6-heatsink_thickness, h = rear_spring_w);
- translate([0, 0, -infty/2+epsilon])
- cube(infty, center=true);
- };
-};
+ cube([rear_spring_center_w, rear_spring_w, wall_thickness],
+ center=true);
+ translate([0, rear_spring_w/2-wall_thickness/2,
+ (led_zoff-heatsink_thickness)/2])
+ cube([rear_spring_center_w,
+ wall_thickness, led_zoff-heatsink_thickness],
+ center=true);
+ translate([0, -rear_spring_w/2+wall_thickness/2,
+ (led_zoff-heatsink_thickness)/2])
+ cube([rear_spring_center_w,
+ wall_thickness, led_zoff-heatsink_thickness],
+ center=true);
+
+ for (angle=[0, 180]) {
+ rotate([0, 0, angle])
+ translate([5.5, 0, rear_spring_h/2])
+ rotate([0, 0, 45]) {
+ cube([wall_thickness, 14, rear_spring_h],
+ center=true);
+ }
+ }
+}
module heatsink_holder() {
for (angle = [0, 180]) {
rotate([0, 0, angle])
- translate([9.1+wall_thickness, 0, 6/2])
- cube([3.5/2+wall_thickness, 2*9.1-3.5-0.5, 6], center=true);
+ translate([rear_pin_dist+wall_thickness, 0, (led_zoff+wall_thickness)/2])
+ cube([rear_pin_diam/2+wall_thickness, 2*rear_pin_dist-rear_pin_diam-2, led_zoff+wall_thickness], center=true);
}
}
cube([infty, 0.5, infty]);
// cable hole, 2*3mm
- translate([9.1, 0, 6+3])
+ translate([rear_pin_dist, 0, 6+3])
rotate([0, 0, 60])
cube([infty, 2, 3]);
// side LED hole, 3mm
translate([0, 0, fraen_h - pin_len])
rotate([90, 0, 0])
- cylinder(r=3.5/2, h=infty, $fn=6);
+ cylinder(r=rear_pin_diam/2, h=infty, $fn=6);
};
rear_spring();
heatsink_holder();
};
-difference() {
- union() {
- lens_holder($fn = 128);
-
-translate([20, 40, 0])
- rotate([90, 0, -90])
- seat_clip(, $fn=128);
-
-hull() {
- translate([0, 9.1+3.5/2+epsilon, wall_thickness/2])
- cube([9.1, epsilon, wall_thickness], center=true);
- translate([20-clip_wall/2, 40-clip_space/2-clip_wall+epsilon, wall_thickness/2])
- cube([9.1, epsilon/2, wall_thickness], center=true);
+module full_joint() {
+ difference() {
+ hull() {
+ intersection() {
+ rotate([-90, 0, 0])
+ scale([0.25, 1, 1])
+ cylinder(r = fraen_h-pin_len, h = rear_pin_dist + wall_thickness+rear_pin_diam/2);
+ translate([-infty/2, rear_pin_dist + wall_thickness + rear_pin_diam/2 - epsilon, 0])
+ cube(infty);
+ };
+ translate([clip_x_off, clip_y_off, 0])
+ intersection() {
+ seat_clip_rotated();
+ translate([(fraen_h-pin_len)*tan(clip_angle)-clip_wall, -clip_space/2-0.1*clip_wall+epsilon, 0])
+ rotate([90+clip_x_rot, 0, 0])
+ scale([0.45, 1, 1])
+ cylinder(r = fraen_h-pin_len, h = epsilon);
+ };
+ };
+ hull() {
+ translate([0, 0, fraen_h - pin_len + epsilon])
+ cylinder(r = fraen_diam/2 + pin_diam/2 + wall_thickness/2,
+ h = epsilon);
+ for (angle = [0, 90, 180, 270])
+ rotate([0, 0, angle])
+ translate([rear_pin_dist, rear_pin_dist, -epsilon])
+ cylinder(r=wall_thickness/2+3.75/2, h = epsilon);
+ };
+ }
};
-hull() {
- translate([0, 9.1+3.5/2+epsilon, wall_thickness/2])
- cube([2*.259+3.5, epsilon, wall_thickness], center=true);
- translate([20-clip_wall/2, 40-clip_space/2-clip_wall+epsilon, wall_thickness/2])
- cube([clip_h1+clip_wall, epsilon/2, wall_thickness], center=true);
+module seat_clip_rotated() {
+ difference() {
+ translate([clip_space/2+clip_wall, 0, 0])
+ rotate([clip_x_rot, 0, 0])
+ translate([-clip_space/2-clip_wall, 0, sin(clip_x_rot)*(clip_space/2+clip_wall+epsilon)])
+ seat_clip();
+ translate([-infty/2, -infty/2, -infty])
+ cube(infty);
+ };
};
-
-translate([7.5, 13.3, 0])
- cube([wall_thickness, 23, fraen_h - pin_len - wall_thickness]);
-
- }
-/*
- translate([-infty/2, -infty/2, 8])
- cube(infty);
-*/
+
+module main() {
+ lens_holder();
+ translate([clip_x_off, clip_y_off, 0])
+ seat_clip_rotated();
+ // xy_joint();
+ // yz_joint();
+ full_joint();
};
+// scale([1, -1, 1]) main($fn=128);
+main($fn = 128);
// vnitrni prumer kruhu by mel byt 30.75mm
// vnejsi prumer aspon 35 mm
// pin od stredu 10.35mm na x a y
https://www.fi.muni.cz/~kas/git / bike-lights.git / blobdiff